PRODUCTS :: Deutsch Connectors -

Deutsch Connectors

PARTS LISTS Click below to Download Deutsch PDF documents

___________________________________

DEUTSCH DT SERIES CONNECTORS (13amp)

Standard inline Y Connector Flange/Panel Mount

For wire to wire connection applications on ENGINES, TRANSMISSIONS, EQUIPMENT CHASSIS, HYDRAULIC VALVE BANKS, INSIDE OPERATOR CABS & CONTROL CABINETS. Deutsch DT Series Connectors offer reliability and performance in harsh environmental conditions. Deutsch DT Series Connectors are now an industry standard connector constructed with thermoplastic housings and silicone seals employed with either solid-copper or nickel-plated stamped and formed crimp type terminals which require no special tools for insertion or removal. With the high quality construction of Deutsch DT series Connectors you can be sure they are well environmentally sealed. Deutsch DT Series connectors are available in 2, 3, 4, 6, 8 & 12-pin configurations and accept wire sizes 0.75mm2 (18AWG) through to 2.5mm2 (14 AWG).

Rugged thermoplastic housings
Integral connector latches
Silicone seals
Crimp contacts - gold or nickel, solid
Current Rating up to 13 amps
Fail safe secondary locks
Hand insertable/removable contacts
Engine Compartment Rated
Meets most harness design requirements
Compatible with Varpren 'F' & Other Wires
Superior environmental seal
No special tools required. Low installation cost
Available in Flange/Panel mount 3, 4, 8 & 12 Pin Configurations

___________________________________

DEUTSCH DT SERIES CONNECTORS CAT BLACK spec (13amp)

Available with Reduced Wire Seal (E Seal)

Deutsch DT series CAT Black spec Connectors maintain all the features and specifications of the above DT series connectors with enhanced features.

Enhanced seal & retention lock
Rear seal end cap
Available with reduced wire retention E Seal
Black housing with green wedgelock for identification
2,3,4,6,8 & 12 Pin Configurations
Suits wire sizes 0.75mm2 (18AWG) through to 2.5mm2 (14AWG)
Crimp contacts - Gold or Nickel Solid
Current rating up to 13Amps

___________________________________

DEUTSCH DTM SERIES CONNECTORS (7.5 Amp)

DEUTSCH DTM Series connectors are designed for all smaller wire gauge applications. The DTM connector line was developed to fill the need for lower amperage, multi- pin, inexpensive connectors. The DTM Series offers the ability to use multiple size 20 contacts, each with 7.5 amp continuous capacity, within a single shell.

2, 3, 4, 6, 8 & 12 Pin Configurations
Suits wire size 0.52mm2 (20AWG)
Crimp Contacts - Gold Or Nickel Solid
Current rating 7.5 Amp
Rectangular, thermoplastic housing
Integrated latch for mating
Wedgelocks assure contact alignment and retention

___________________________________

DEUTSCH DTP POWER SERIES CONNECTORS (25amp)

Standard inline Flange/Panel Mount

2 & 4 Pin Configuration
Suits Wire sizes 12AWG
Current Rating 25amp
Available in Flange/Panel mount 4 Pin Configuration

___________________________________

DEUTSCH DTHD POWER SERIES CONNECTORS (100amp)

Single Pin Configuration
Suits wire sizes 4AWG, 8AWG, 12AWG
Current Rating 60amp to 100amp.

___________________________________

DEUTSCH DTCE POWER SERIES CONNECTORS (100amp extended contacts)

Single Pin Configuration
Suits wire size 4AWG only
Current Rating 60amp to 100amp

___________________________________

DEUTSCH DT SERIES BUSSED RECEPTACLES

These standard "DT" receptacle shells feature internal pin type contact buss bar arrangements that allow common connections from 3 to 12 using size 16 contacts. Buss bars are available in standard nikel or gold to mate with common Deutsch Industrial Products contacts. Other features include the use of standard "DT" plugs to mate with these environmental receptacles. Plugs with any Deutsch modifications are intermatebale.

Meets all performance specifications of the standard "DT" series.
Bus bar material - copper alloy. All other materials are the same as standard "DT" series.
Bussed receptacle comes assembled complete with standard "DT" wedges pre-installed.

BUSSED RECEPTACLE CONFIGURATIONS:

4 PIN BUSS

1 x 4 Pin Buss - 26amps

6 PIN BUSS

1 x 6 Pin Buss - 39amps
2 x 3 Pin Buss - 13amps each

8 PIN BUSS

1 x 8 Pin Buss - 52amps
2 x 4 Pin Buss - 26amps each
1 x 3 & 1 x 5 Pin Buss - 26amp

12 PIN BUSS

1 x 12 Pin Buss - 76amps
2 x 6 Pin Buss - 39amps each
4 x 3 Pin Buss - 13amps each

___________________________________

DEUTSCH HD30 SERIES CONNECTORS (13 Amp to 100 Amp)

DEUTSCH HD30 Series connectors are constructed from a metal shell developed to meet the needs of the heavy duty mining, construction & transpot equiopment industries. The HD30 features include quick connect-disconnect bayonet coupling, single hole bulkhead mounting, silicone seals, and a rear insertion/rear removal contact system.

Accepts contact sizes 4 (100Amp), 8 (60Amp), 12 (25Amp), 16 (13Amp),
In-line or flange mount
Circular, aluminum housing
Coupling ring for mating
9 & 31 Pin Configurations (others available)
Crimp Contacts - Nickel Solid

___________________________________

DEUTSCH DRC SERIES CONNECTORS (13 Amp)

The environmentally sealed DRC series is a rectangular connector series that offers insert arrangements of 24, 40 and 70 cavities and accept size 16 contacts.

Accepts Contact size 16 (13 Amp)
Suits wire sizes 0.75mm2 (18AWG) through to 2.5mm2 (14AWG)
Crimp contacts - Gold or Nickel Solid
Rectangular, thermoplastic housing
Flange/Panel Mount
24, 40 & 70 Pin Configurations (others available)

___________________________________

DEUTSCH ACCESSORIES

Mounting Clips

Plastic Zinc Steel 90Deg Stainless Steel

Deutsch Connector mounting clips allow you to securly mount a connector to a structure helping avoid damage to the connection and associated wiring. There are 4 types available - Stainless steel straight, Zinc metal 90deg, Plastic - 8way housing, Plastic - 2,3,4,6 & 12 way housings

___________________________________

Crimpers

A variety of crimp tools are available to suit the full range of Deutsch solid contacts. Suits Deutsch Solid Crimp Contact Sizes 22, 20, 18, 16, 12, 8 ,4